Shell Heat Transfer Oil S2 Performance, Features & Benefits:
- + Extended maintenance intervals
- + System efficiency
- + Wear protection
Performance, Features & Benefits of Shell Heat Transfer Oil S2
+ Extended maintenance intervals
Shell Heat Transfer Oil S2 is based on carefully selected highly refined mineral oils and resists oil cracking, oxidation and thickening. This provides extended oil life, provided efficient fluid heating and good pump circulation is ensured, such that film temperatures on the heater surface do not exceed the limits above.
+ System efficiency
Low viscosity enables excellent fluidity and heat transfer over a wide temperature range. Shell Heat Transfer Oil S2 also has a low vapour pressure so resists cracking. This minimises the formation of volatile decomposition products; these would require recovery via expansion chamber and condensate collector.
+ Wear protection
Shell Heat Transfer Oil S2 is non-corrosive and has high solvency – this reduces deposit formation by holding oxidation products in solution and keeping internal surfaces of heat exchangers clean.
If you have any questions, please contact Procare Technical Helpdesk
Health, Safety & Environment of Shell Heat Transfer Oil S2
Health and Safety
Shell Heat Transfer Oil S2 is unlikely to present any significant health or safety hazard when properly used in the recommended application and good standards of personal hygiene are maintained. Avoid contact with skin. Use impervious gloves with used oil. After skin contact, wash immediately with soap and water. Guidance on Health and Safety is available on the appropriate Material Safety Data Sheet, which can be obtained from http://www.epc.shell.com/
Protect the Environment
Take used Shell Heat Transfer Oil S2 to an authorised collection point. Do not discharge into drains, soil or water.
Typical Physical Characteristics of Shell Heat Transfer Oil S2
| Properties |
|
|
Method |
Shell Heat Transfer Oil S2 |
| Density |
@20°C |
kg/m3 |
ISO 12185 |
857 |
| Flash Point (PMCC) |
– |
°C |
ISO 2719 |
208 |
| Flash Point (COC) |
– |
°C |
ISO 2592 |
220 |
| Pour Point |
– |
°C |
ISO 3016 |
-12 |
| Kinematic Viscosity |
@40°C |
mm2/s |
ISO 3104 |
29 |
| Kinematic Viscosity |
@100°C |
mm2/s |
ISO 3104 |
5.1 |
| Kinematic Viscosity |
@200°C |
mm2/s |
ISO 3104 |
1.4 |
| Initial Boiling Point |
– |
°C |
ASTM D2887 |
330 |
| Auto ignition temperature |
– |
°C |
DIN 51794 |
332 |
| Neutralisation Value |
– |
mg KOH/g |
ASTM D974 |
<0.2 |
| Ash (Oxid) |
– |
% m/m |
ISO 6245 |
<0.01 |
| Carbon Residue (Conradson) |
– |
% m/m |
ISO 10370 |
0.01 |
| Copper Corrosion (3 hrs) |
– |
– |
ISO 2160 |
Class 1 |
| Coefficient of Thermal Expansion 1/0C |
– |
– |
– |
0.0008 |
Specific heat of Shell Heat Transfer S2 32:
| Shell Heat Transfer S2 32 Specific heat, KJ / kg K |
|
| At 20C |
1.853 – 1.878 |
| At 100C |
2.140 – 2.170 |
| At 200C |
2.499 – 2.534 |
| At 300C |
– – 2.898 |
Coefficient of thermal conductivity of Shell Heat Transfer S2:
| Shell Heat Transfer S2 32 coefficient of thermal conductivity, W / mK |
|
| At 20C |
0.130 – 0.134 |
| At 100C |
0.124 – 0.128 |
| At 200C |
0.118 – 0.121 |
| At 300C |
– – 0.114 |
Is Shell Thermia the same as Shell Heat Transfer Oil S2?
Shell Heat Transfer Oil S2 is the direct successor of Shell Thermia. The performance of Shell Heat Transfer Oil S2 is the same as Shell Heat Transfer Oil S2, only a name change has occurred.
Can I also use Shell Heat Transfer Oil S2 in an open system?
No, Shell Heat Transfer Oil S2 is not suitable for open systems. Be careful, this can lead to dangerous situations! For open systems Procare has a good solution, but please contact Procare because they can advise you if it is possible and how it is possible.
Where can I buy Shell Heat Transfer Oil S2?
Procare is the largest online lubricant webshop with exclusively world famous brands including Shell Heat Transfer Oil S2. Customers of Procare appreciate the convenience and time saving that they can buy lubricants online 24/7 at a competitive price. Questions are no problem: Knowledge is our strength!
